Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Sign in to follow this  

pulley problem

Recommended Posts

I just recieved my bevel gear shaft pulley after 3wks.of waiting but I dont think it is correct the original pulley was a stamped steel one and it was a little larger in diameter. The new one part no.157694 is a cast unit 04.300 od and 0.876 id. it seems a little too snug to fit on the bevel gear shaft on my 64 landlord is this the correct replacement to drive my mower pto? or can Ijust have it machined to fit on the shaft and use it ? IF I HAVE TO WAIT ANOTHER 3WKS IT WILL LOOK LIKE JUNGLE AROUND HERE!!!(JUST KIDDING) THANKS JBLACK.

Share this post

Link to post
Share on other sites
Hi jblack, Ok now remember I measured mine on the tractor so please take that into account. The pulley is a stamped one and it measures approx. 5"dia. and my shaft measures 7/8"dia.-Now my manual is showing a part# of-157121 and that looks like a stamped steel one. I hope this helps you.-->jackl<--

Share this post

Link to post
Share on other sites
Hi Again jblack, the pulley # that I gave you is the # of the pulley I have on my 1964 landlord write now. And I have had it for 15 years and its the same one that came on it then. The pulley should be snuck sliding on the shaft and not to the point of having to hammer it on. You should be able to file the set screw marks off the shaft and then put some oil on and slide the new one on if its the write one. Call Mark at University Lawn and make sure it is the write one. Its long distance and he might be busy "BUT" tell them its a long distance call and hopefully Mark can get write with you.#248-3737220 if your interested. Good Luck again-->jackl<--

Share this post

Link to post
Share on other sites
This topic is now closed to further replies.
Sign in to follow this  

  • Who's Online (See full list)

    • Snojetter
    • BLT
    • BryanJ
    • gwiseman
    • stew2YWP
    • MARK (LI)
  • Today's Birthdays

    1. JoggerFogger
      (49 years old)
  • Recent Status Updates

    • Paul M.Murphy

      Paul M.Murphy

      Hello glad I got on this site. I hope to upload a couple of photos of my Simplicity Broadmoor 
      Model 707 Tractor. I have replaced all the belts on it and installed a new ignition switch.
      Have a mower deck which was in poor shape , repaced a couple of bushings and welded the
      deck where there was some holes. The tractor and mower deck came from a friend and the 
      mower deck metal was getting pretty thin. Some new metal was put in it and we also undercoated the underside of the deck. This was done by my friend Greg Toulman.
      I have not put the mower deck on the tractor yet, waiting for Greg to come home and give me a hand. Can you please tell me if there is a manual for the mower deck and where I could get one.
      I would also like to get some moon wheel discs as well.
      I will try and down load some photos of the tractor when my wife shows me how to. 
      I really love driving this tractor and also how well it is made compare today's tractors, especially the flexible rear end and the rollers.
      Tell the next time 
      · 8 replies
    • jbrooks

      jbrooks  »  Talntedmrgreen

      folowing  this from a link at the downloads.  I just rescued an AC 920 with the lambodini diesel. I can' t download  yet .  Where did you find the PDF copy you posted. . I would like to figure out how to adjust the injection pump. 
      I assume it's a bosche, correct
      · 0 replies
  • Adverts