Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Sign in to follow this  
plh_in

Choke & Puke...not hamburgers...Help!

Recommended Posts

plh_in
I have an '86 DeutzAllis 916H. I had not had it very long when after mowing for a while it would pretty much flood itself & barely run. So...I put in a new inlet needle, baffle gasket, bowl gasket, float pin, and a new fuel inlet seat [though the new one was shaped a little different...?]. In any event, the tractor will start & run if the throttle is wide open. If I try to throttle it back, it wants to flood almost instantly & I cannot keep it running. Its so bad gas will run from the carb. Do I need to get another fuel inlet seat? Anything else I should be looking at???? Its running worse now than when I started messing w/ it!! Any help is greatly appreciated! The grass is growing & I cannot stop it!! - Pat

Share this post


Link to post
Share on other sites
HubbardRA
Sounds like you have the same problem that I have. The float sounds like it is taking on gas and sinking. Remove the float, and hold it up to your ear and shake it to see if there is fuel inside. If not, then you may have a leak around the siphon tube where it goes through the fuel bowl. Make sure that is seated tightly. The seat you are talking about can be easily checked. Remove the fuel bowl, then re-mount the carb and hook up the fuel line. Turn on the gas and hold the float up to seat the needle. If fuel comes out around the needle or under the seat, then the seat is definitely your problem. If you do not get many responses to your post, then you should think about joining the club. Only $10/year. Club members get more attention than outsiders.

Share this post


Link to post
Share on other sites
bigcountry
I was thinking it's a bad float too. I had an old Tecumseh tiller that I had that problem with. It would run wide open, and then when I'd back off on the gas, it would just flood out and die. I ended up just junking it, because it was such a pain to work on.

Share this post


Link to post
Share on other sites
maxtorman1234
I'd check the float too, I had a carb on my 310, It would start and run fine, but every 10-15 minutes it would flood and stall, and the gas would drip out.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Who's Online (See full list)

    • GregB
    • jackcobb
    • rokon2813
    • spi
    • simplewrench
    • ShaunE
  • Today's Birthdays

    1. 720nut
      720nut
      (66 years old)
    2. Joe Scann
      Joe Scann
      (79 years old)
  • Recent Status Updates

    • Paul M.Murphy

      Paul M.Murphy

      Hello glad I got on this site. I hope to upload a couple of photos of my Simplicity Broadmoor 
      Model 707 Tractor. I have replaced all the belts on it and installed a new ignition switch.
      Have a mower deck which was in poor shape , repaced a couple of bushings and welded the
      deck where there was some holes. The tractor and mower deck came from a friend and the 
      mower deck metal was getting pretty thin. Some new metal was put in it and we also undercoated the underside of the deck. This was done by my friend Greg Toulman.
      I have not put the mower deck on the tractor yet, waiting for Greg to come home and give me a hand. Can you please tell me if there is a manual for the mower deck and where I could get one.
      I would also like to get some moon wheel discs as well.
      I will try and down load some photos of the tractor when my wife shows me how to. 
      I really love driving this tractor and also how well it is made compare today's tractors, especially the flexible rear end and the rollers.
      Tell the next time 
      Paul
       
      · 9 replies
    • jbrooks

      jbrooks  »  Talntedmrgreen

      Josh
       
      folowing  this from a link at the downloads.  I just rescued an AC 920 with the lambodini diesel. I can' t download  yet .  Where did you find the PDF copy you posted. . I would like to figure out how to adjust the injection pump. 
      I assume it's a bosche, correct
      · 0 replies
  • Adverts

×