Alpha8D 0 Posted October 8, 2005 Wiindshield washer fluid -25F stuff 94 cents a gallon at Walmart last night. Check your store. Bought 12 gals and ready to try it this evening. Just hoping my wimpy paint compressor w/o tank will seal the beads again. It's got the pressure, just wimpy volume and no tank. I'll be real careful to only break one bead enough to drizzle the juice in. I'm assuming I need some air in there to keep them pressurized and not too hard. I don't have tubes. Share this post Link to post Share on other sites
D-17_Dave 12 Posted October 8, 2005 The normal amount is ussually at or just above the top of the rim w/ the tire standing up. This will allow you enough air to keep the tires inflated and allow for temp. exspantion. Share this post Link to post Share on other sites
Alpha8D 0 Posted October 10, 2005 DONE! I put 7.5 gals in each rear tire. Laying on their side that was still about 1/2" below where the bead seals on the rim. Tough to break the bead, took a 2x4, smll block of wood and 2 bar clamps but they finally popped down. Re-seating the beads just happened by itself after block was removed and the tire relaxed back onto rim. No problem. Rear wheels now weigh 85# each without any wheel weights. Mowed hilly church lawn Sun evening and no longer tippy. Climbed straight up the hill with no slipping too! Very happy! Tires are 10.5" wide on 12" rims. Share this post Link to post Share on other sites
patrician12 0 Posted October 10, 2005 It's such a inexpensive and brillant way to solve a problem.It's so brillant it's stupid. Share this post Link to post Share on other sites
KVANDY12 0 Posted October 10, 2005 Don't you just love it when a plan comes together and everything works out Share this post Link to post Share on other sites
D-17_Dave 12 Posted October 10, 2005 It's amaising the Simplicity of it all. Share this post Link to post Share on other sites
xrisj 0 Posted October 12, 2005 I'd never heard of such a thing before I joined this group. I'm thinking of filling up my car tires! (not...) Share this post Link to post Share on other sites
comet66 0 Posted October 13, 2005 Takes a little more effort to fill and burp a tubed tire, but well worth it. Share this post Link to post Share on other sites
a7117puller 0 Posted October 16, 2005 better put in an order for another set of rims. doin that will eat em up Share this post Link to post Share on other sites
MPH 12 Posted October 16, 2005 -25f..Wonder how long I could be out blowing snow at -40 before my tires got square:D Share this post Link to post Share on other sites
Alpha8D 0 Posted October 16, 2005 Didn't mention it but I also added 1/2 gal of antifreeze with rust inhibiter in each tire. Can't hurt. Calcium Chloride would certinly eat rims up but I doubt this will. Any other opinions? Share this post Link to post Share on other sites
ehertzfeld 1 Posted October 17, 2005 quote:Originally posted by a7117puller better put in an order for another set of rims. doin that will eat em up Please explaine how Washer Fluid will rust out a rim. I do belive only water and salt will rust steel and there is no water or salt in washer fluid. It's a oil based substance isnt it? All I can see happening, "over a long time", is the rubber will break down. I have a few loaded with WW and have had no problems, except having too much traction. I have no fear plowing snow and somtimes push too far.:D:D:D Share this post Link to post Share on other sites
a7117puller 0 Posted October 18, 2005 re-read your label, and moisture of anyform will Share this post Link to post Share on other sites
UCD 14 Posted October 18, 2005 Adam The tires and wheels on my 7790 loaded with Calcium Chloride are older than you are. The tires and wheels were on my 1970 Bolons 14hp then on my 1975 Simplicity7016 Then on my 1985 7790. It is not the combination of Calcium Chloride and water that causes them to rust though, you also need oxygen. As long as the tires remain sealed the wheels will not rust though. Share this post Link to post Share on other sites