Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Sign in to follow this  
rsnik

Points eliminator

Recommended Posts

rsnik
Here is what the points eliminator looks like as installed in (or in this case near) the points box. I would not do it this way again. It's an electronic component it should be installed in the console area. All the wires can be routed up there. The instructions say moisture is not issue but heat is an issue. So this activity does not need to happen in this area anymore (if this sounds like the new high school sex ed classes I apologize). I kept the retainer that holds the plunger boot in place and had to fiddle with things until oil quit leaking. When I was done the results wont hardly fit in the points box and since heat is an issue you likely don't want the points cover on anyway.


After that I put on new rollers and painted the bottom of the deck. If you bought new 4" rollers they have now feature 3/4 inch i.d. instead of 5/8. Won't work. I also discovered the rod on my antiscalp rollers had wore a one inch hole where the rod terminates in the baffle. Turns out my junk deck has a perfect baffle with perfect rollers and the rollers on the wore out rod on my "good" deck were perfect because they have not touched the ground in a long time. They are 4 inch rollers! What a wonderful thing it is to get perfection out of a bunch of junk!


Share this post


Link to post
Share on other sites
Paul_B
After trying to squeeze my electonic module under the points cover, I gave up and mounted it on the vertical part of the frame just behind the motor. This should be a cool and lower vibration area. It's also easy to access if I need to replace it.

Share this post


Link to post
Share on other sites
BLT
My Sten's Meg-Fire has been mounted on the point box for nearly fifteen years and no problem. I also wired it thru the points as I had an occasional 'popping' when trying to start it. Wiring it thru the points eliminated that. I also adjusted points to stay closed longer. Not a problem to date.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Who's Online (See full list)

    • RayS
    • dhoadley
    • Ronald Hribar
  • Today's Birthdays

    1. Mike_H
      Mike_H
      (43 years old)
  • Recent Status Updates

    • Paul M.Murphy

      Paul M.Murphy

      Hello glad I got on this site. I hope to upload a couple of photos of my Simplicity Broadmoor 
      Model 707 Tractor. I have replaced all the belts on it and installed a new ignition switch.
      Have a mower deck which was in poor shape , repaced a couple of bushings and welded the
      deck where there was some holes. The tractor and mower deck came from a friend and the 
      mower deck metal was getting pretty thin. Some new metal was put in it and we also undercoated the underside of the deck. This was done by my friend Greg Toulman.
      I have not put the mower deck on the tractor yet, waiting for Greg to come home and give me a hand. Can you please tell me if there is a manual for the mower deck and where I could get one.
      I would also like to get some moon wheel discs as well.
      I will try and down load some photos of the tractor when my wife shows me how to. 
      I really love driving this tractor and also how well it is made compare today's tractors, especially the flexible rear end and the rollers.
      Tell the next time 
      Paul
       
      · 8 replies
    • jbrooks

      jbrooks  »  Talntedmrgreen

      Josh
       
      folowing  this from a link at the downloads.  I just rescued an AC 920 with the lambodini diesel. I can' t download  yet .  Where did you find the PDF copy you posted. . I would like to figure out how to adjust the injection pump. 
      I assume it's a bosche, correct
      · 0 replies
  • Adverts

×