Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Sign in to follow this  
donmoore1904

Leak at input shaft - 3sp transmission

Recommended Posts

donmoore1904
I have a leak at the input shaft to my 3-sp transmission. I am currently taking the transmission apart to replace the axle tube. My question is what is supposed to seal the input shaft opening in the case. I don't know anything about "sealed" bearings, but a bearing is the outer-most element on this shaft (with the pulley/hub removed, I can see the bearing). It is item 86 in the 3-sp diagram. The pulley hub was damp, and when I pulled it off, the shaft was soaked with oil. Any advice would be greatly appreciated. I found I wasn't that low on oil when I drained it, but of course I would like to fix this while I have it torn down. Don

Share this post


Link to post
Share on other sites
donmoore1904
I just figured out this is the same bearing as the mower deck spindles (2018202). I don't believe that bearing is capable of sealing in oil. I think they rely on washers to block oil. I found a discrepancy between what I found and what is in the diagram. When I pulled the cover off, I found a thin washer followed by a shoulder washer that rides against a snap ring. The diagram doesn't show the thin washer. It is possible a previous owner didn't get it assembled correctly. That thin washer may be the one for under the retaining ring for the bearing. I have another 3-sp trans - I think I'll take it apart to see what is in that one, and also to check the Drive Gear, mine has worn keyways. It sure is fun disassembling these transmissions sm00

Share this post


Link to post
Share on other sites
donmoore1904
Turns out the diagram is correct. The ring shown in between (retaining ring for the bearing) is so large the thin washer could be shown on either side. This thin washer is what seals the opening, by bearing against the inner race. The washer is very worn on my good machine where the inner race bears on it (maybe a .003" groove). In the spare trans, the washer is smooth. Also, the input shaft is just a hair smaller on the good machine. So I am going to swap input shafts and thin washers, and hope for the best.

Share this post


Link to post
Share on other sites
donmoore1904
After puttering along with two transmissions split open for several days, I have a different take on my pulley (input) shaft oil leak. I initially thought the worn thin washer just inside the bearing was the cause, not understanding this bearing is sealed. I detected a very slight distortion in the bearing cover, and my guess now is the person who installed it hit the cover and/or the inner race. This caused the race to not butt against the washer uniformly, and thus the excessive wear on the washer. Once I saw the new bearing is indeed sealed, I went back to questioning my thinking...

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Sign in to follow this  

  • Who's Online (See full list)

    • rich_kildow
    • MRR
    • simplewrench
    • tripleguy
    • MARK (LI)
  • Today's Birthdays

    No users celebrating today
  • Recent Status Updates

    • dav-1

      dav-1  »  Talntedmrgreen

        Over a year ago, you answered a question I had about the tool bar for my FDT. In your reply dated Dec 31, 2019  you said the spacer, part #16, goes in the bar to allow for up and down depth adjustment. does this mean the bolt has to be tightened at whatever depth desired or does the bolt slide up and down, allowing the lower hitch to free float?
         If it is tightened so the lower hitch and the bar are rigid, then is the depth to be controlled by the shoes? Or by the lift handle?
        Is there any kind of user directions for the tool bar? The Outdoor Power Manual basically shows how to assemble the bar but not how to use it
      · 1 reply
    • tribswede

      tribswede  »  goatfarmer

      ISO a deck for a 6516 H and all the connecting hardware any ideas on where to start?
       
      · 1 reply
  • Adverts

×