Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Sign in to follow this  
mendon-chalmers

allis mow bee

Recommended Posts

jfrank1962
This one is on a load of Allis stuff I saw at the Florida Flywheelers a few years ago. http://www.simpletractors.com/club2/topic.asp?ARCHIVE=true&TOPIC_ID=106496&SearchTerms=mow,bee

Share this post


Link to post
Share on other sites
mowinman2
I have one. The transmission is setup somewhat like a snapper with the friction disc drive. Mine is out of commission due to the worn out disc and missing parts. The little briggs on the back sure runs nicely though. I dont have a picture of mine but i did see one at a show a couple months ago. Here is that pic [IMG]http://i1023.photobucket.com/albums/af355/Iluvtruks0/Arden%2010-21-11/IMG_1023.jpg[/IMG] [IMG]http://i1023.photobucket.com/albums/af355/Iluvtruks0/Arden%2010-21-11/IMG_1024.jpg[/IMG] [IMG]http://i1023.photobucket.com/albums/af355/Iluvtruks0/Arden%2010-21-11/IMG_1025.jpg[/IMG] [IMG]http://i1023.photobucket.com/albums/af355/Iluvtruks0/Arden%2010-21-11/IMG_1026.jpg[/IMG]

Share this post


Link to post
Share on other sites
D-17_Dave
We had a 7HP version Mow-Bee when I was very young. tranny being pretty crappy and they were definitely built to compete with the cheaper smaller line of mowers like Snapper at the time. But these did have a cast aluminum deck and timed blades. Very advanced for it's years and mowed VERY well. The Scamper models were somewhat basic replacements for these and again they used friction cone drive tranny setups that were a complete disaster. The Scamps had stamped decks but did have timed blades as well. I don't recall ANY deck that mowed as well as the timed deck I had on the 7HP Scamp I had. I should have never traded it off to Craig.....

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Sign in to follow this  

  • Who's Online (See full list)

    • Koabd1978
    • Bear
    • red93
    • AC B-112 Driver
    • BLT
    • B-1 Bryan
    • Brettw
    • bnolt
    • midnightpumpkin
    • deebig
    • NateShedivy
    • littlefan
  • Today's Birthdays

    No users celebrating today
  • Recent Status Updates

    • dav-1

      dav-1  »  Talntedmrgreen

        Over a year ago, you answered a question I had about the tool bar for my FDT. In your reply dated Dec 31, 2019  you said the spacer, part #16, goes in the bar to allow for up and down depth adjustment. does this mean the bolt has to be tightened at whatever depth desired or does the bolt slide up and down, allowing the lower hitch to free float?
         If it is tightened so the lower hitch and the bar are rigid, then is the depth to be controlled by the shoes? Or by the lift handle?
        Is there any kind of user directions for the tool bar? The Outdoor Power Manual basically shows how to assemble the bar but not how to use it
      · 1 reply
    • tribswede

      tribswede  »  goatfarmer

      ISO a deck for a 6516 H and all the connecting hardware any ideas on where to start?
       
      · 1 reply
  • Adverts

×