Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Sign in to follow this  
stevieB

Spindle for mower b210

Recommended Posts

SmilinSam
As far as I know the spindles are pretty much the same for a variety of models. The rare piece on the 210 is the double pulley which sits atop the center spindle shaft. However, I noted looking through some literature that there was a replacement single pulley kit offered to do away with the double belt setup. I'm sure Sandy Lake Implement (advertiser here on the site)would have something to help you out, or I and or others here could come up with something. I do not like rebuilding the older spindles because thet are hard to get apart without ruining one thing or another. Sam

Share this post


Link to post
Share on other sites
johnmonkey
I just replaced my center spindle (dble pulley type) on my 1962 mongomery ward mower deck. The same as a simplicity 725. Sandy Lake was most helpful, they even faxed me some drawings of my mower deck. I also replaced the bearings and it runs great. John

Share this post


Link to post
Share on other sites
Kent
Just to clarify. The pulley/belt setup that Sam was referring to is a type 3V, 13/16" wide double-V belt, as shown below. It was used on at least some of the 1969-1970 model Landlords, Sovereigns and equivalent AC B-210 and B-212s. I don't think ALL of these models used it, but I'm not sure. There was a later "kit" to convert them to a standard V-belt... My B-210 still uses them. They're expensive ($40 plus) but VERY tough. I've slung mine off several times without damaging it when the deck suddenly drops off something that's a few inches tall -- like a curb, ditchbank, etc. -- and the deck drops down farther than the "PTO preload" spring can compensate for quickly.... http://www.simpletractors.com/parts/belts/cs_3v.gif

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Who's Online (See full list)

    • s_stephen
    • jbrooks
    • dplakosh
    • mikeandlina
    • deebig
    • lt-scir
    • ac.d17iv
    • NateShedivy
    • rokon2813
  • Today's Birthdays

    1. Look Out Hill
      Look Out Hill
  • Recent Status Updates

    • Paul M.Murphy

      Paul M.Murphy

      Hello glad I got on this site. I hope to upload a couple of photos of my Simplicity Broadmoor 
      Model 707 Tractor. I have replaced all the belts on it and installed a new ignition switch.
      Have a mower deck which was in poor shape , repaced a couple of bushings and welded the
      deck where there was some holes. The tractor and mower deck came from a friend and the 
      mower deck metal was getting pretty thin. Some new metal was put in it and we also undercoated the underside of the deck. This was done by my friend Greg Toulman.
      I have not put the mower deck on the tractor yet, waiting for Greg to come home and give me a hand. Can you please tell me if there is a manual for the mower deck and where I could get one.
      I would also like to get some moon wheel discs as well.
      I will try and down load some photos of the tractor when my wife shows me how to. 
      I really love driving this tractor and also how well it is made compare today's tractors, especially the flexible rear end and the rollers.
      Tell the next time 
      Paul
       
      · 0 replies
    • jbrooks

      jbrooks  »  Talntedmrgreen

      Josh
       
      folowing  this from a link at the downloads.  I just rescued an AC 920 with the lambodini diesel. I can' t download  yet .  Where did you find the PDF copy you posted. . I would like to figure out how to adjust the injection pump. 
      I assume it's a bosche, correct
      · 0 replies
  • Adverts

×