Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Sign in to follow this  
JBLACK

Model 4040 Questions

Recommended Posts

JBLACK
Would appreciate a manual showing engine breakdown for my Simplicity 4040. Dealer sez stator is shot for it is not charging my battery this season. He has no parts. Any around?

Picked this 4040 up from moving out neighbor for $500 and put another $500 into it. It flat cuts grass with the 60" mower deck.

What tiller would fit this? Model # ?

Share this post


Link to post
Share on other sites
StanS
Here is nearly everything you need except the part #. Connect the giant 48" rotary tiller to the cat 0 three pt. hitch and (factory installed) PTO. Engine speed: minimum 75% (2700 rpm). Tranny: 1st gear. Hydrostatic Lever: to make good 1 mph. I mentioned the 3 pt and PTO because if got them with the 4040 for a measely, tiny $500 .......#$%^&.

Stan

Share this post


Link to post
Share on other sites
Guest
JW

Part number for the tiller is 990696, your tractor should have a 3 pt catergory O hitch with a 2,000 rpm pto, the 4040 tractor according to the book could have been bought without the hitch and rear pto. most of those tractors were sold with the hitch installed at the dealer.any after market tiller with a catergory O hitch and runs at 2,000 rpm's will fit on that tractor. If you need a stator I can order it for you the part is still available, please e-mail me if your interested. Good luck



Mark

Share this post


Link to post
Share on other sites
Guest
There is an aftermarket tiller for the 4040 and 9020 tractors. It is made by Beefco Mfg. Co. in North Carolina and it has the correct shaft you need for the female tractor end and runs at the correct 2000 rpm speed. I have their address if you need it as I bought one for my AC 720. It is fairly expensive but worth every penny as it does a great job. Also, I have a 9020 which has similiar electrical charging problems. My dealer is currently getting parts to fix it but they are quite expensive. If you run the tractor without charging properly and use the front PTO, you can damage the electrical PTO clutch so I'm told. RoyG

Share this post


Link to post
Share on other sites
Guest
There is an aftermarket tiller for the 4040 and 9020 tractors. It is made by Beefco Mfg. Co. in North Carolina and it has the correct shaft you need for the female tractor end and runs at the correct 2000 rpm speed. I have their address if you need it as I bought one for my AC 720. It is fairly expensive but worth every penny as it does a great job. Also, I have a 9020 which has similiar electrical charging problems. My dealer is currently getting parts to fix it but they are quite expensive. If you run the tractor without charging properly and use the front PTO, you can damage the electrical PTO clutch so I'm told. RoyG

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Who's Online (See full list)

    • MrSteele
    • SmilinSam
    • Talntedmrgreen
    • PhanDad
    • Chris727
    • jsciutto
    • mjbarbero
  • Today's Birthdays

    1. mjbarbero
      mjbarbero
      (64 years old)
  • Recent Status Updates

    • Paul M.Murphy

      Paul M.Murphy

      Hello glad I got on this site. I hope to upload a couple of photos of my Simplicity Broadmoor 
      Model 707 Tractor. I have replaced all the belts on it and installed a new ignition switch.
      Have a mower deck which was in poor shape , repaced a couple of bushings and welded the
      deck where there was some holes. The tractor and mower deck came from a friend and the 
      mower deck metal was getting pretty thin. Some new metal was put in it and we also undercoated the underside of the deck. This was done by my friend Greg Toulman.
      I have not put the mower deck on the tractor yet, waiting for Greg to come home and give me a hand. Can you please tell me if there is a manual for the mower deck and where I could get one.
      I would also like to get some moon wheel discs as well.
      I will try and down load some photos of the tractor when my wife shows me how to. 
      I really love driving this tractor and also how well it is made compare today's tractors, especially the flexible rear end and the rollers.
      Tell the next time 
      Paul
       
      · 8 replies
    • jbrooks

      jbrooks  »  Talntedmrgreen

      Josh
       
      folowing  this from a link at the downloads.  I just rescued an AC 920 with the lambodini diesel. I can' t download  yet .  Where did you find the PDF copy you posted. . I would like to figure out how to adjust the injection pump. 
      I assume it's a bosche, correct
      · 0 replies
  • Adverts

×