Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Sign in to follow this  
bowhunt4life

16hp Briggs and B10

Recommended Posts

rokon2813

Sure will.

Footprint is the same, shaft height is the same.

It should have the short dipstick near the bottom of the block. If it has the tall one behind the generator, it will end up under the grill frame without a little tweaking.

Share this post


Link to post
Share on other sites
perry

my bigten has a 16hp with long dipstick out of the block . the grill mount has a round hole cut into it to check oil. i put a 10hp oil pan on it to be able to check the oil without pulling the hood.

Share this post


Link to post
Share on other sites
BLT

10 thru 16 HP Briggs engines have the same envelope dimensions. The only difference is in the 30 CID engines and a few 32 CID engine is that the synchro balance is mounted on the PTO side and some clearance notching is needed to fit them in the round hoods. I R a student of that. My 101 is a 12HP powered tractor.;)

Share this post


Link to post
Share on other sites
SmilinSam

On Engines with the tall dipstick threaded into the block itself, I usually unscrew the dipstick/pipe from the block and install a flush allenhead plug. Then I put a B series stlye pan, with the oil check plug in the pan, on the engine and bolt the engine into the tractor as normal.

Share this post


Link to post
Share on other sites
RandyBuxton

May we see some pictures please? Thanks!

quote:Originally posted by osenga

Yep the above is all said well. My 16hp fit in my B10 just great and no mods. Had to be made


id="quote">
id="quote">

Share this post


Link to post
Share on other sites
superbman101

Sure Does fit!We have 3 Tractors with 16hp engines in them. B10, B10, and B110.Here is the B110 Taking it apart to restore after puller down trees in the woods :P

b11016hp.jpg

b11016hp.jpg.1f2f404552cbf6d79bac751269b40d18.jpg

Share this post


Link to post
Share on other sites
aspeltz1

Is the 16 HP motor that is used to repower B10's and B12's of the same type as the original engines(singe cylinder cast iron Briggs)? What model tractors are these 16 HP engines coming from?

Share this post


Link to post
Share on other sites
BLT
quote:Originally posted by aspeltz1

Is the 16 HP motor that is used to repower B10's and B12's of the same type as the original engines(singe cylinder cast iron Briggs)? What model tractors are these 16 HP engines coming from?


id="quote">
id="quote">3415 thru 7016 tractors with starter generators (belt drive).

Share this post


Link to post
Share on other sites
phtann3

Does anyone know what I will need to do to install vanguard v-twin into my simplicity Baron 3414s. I has a sick single cylinder briggs 14 hp in there now. tahnks

Share this post


Link to post
Share on other sites
RayS

Paul, below is a link to installing a Vanguard.

http://www.simpletractors.com/club2/topic.asp?ARCHIVE=true&TOPIC_ID=86413&SearchTerms=vanguard

There is quite a bit of info. in the archives. Seen a Kohler Command in a 7016 the other day on another site. The Kohler Command takes up more room than either a Briggs Vanguard or a Honda. Space would be limited but it can be done.

http://www.simpletractors.com/club2/search.asp?sectionid=4

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

Sign in to follow this  

  • Who's Online (See full list)

    There are no registered users currently online

  • Today's Birthdays

    No users celebrating today
  • Recent Status Updates

    • Bubba1997

      Bubba1997

      Searching for a Sleeve hitch and breaking plow and other equipment if price is right and also a deck for a B1 thank you 
      · 3 replies
    • Dean McFadden

      Dean McFadden

      Good morning peeps! I’m always searching for helpful information with my AC collection. Hope to find out new information and pass on my own experience in restoration. Here are some pics of my babies. I’m still looking for front rims for the 410 so yesterday I put the 310 wheels on took it for a drive. Working pretty good but still needs some carb work. Gotta get the 310 running next. Have a great day!😁
       

      · 1 reply
  • Adverts

×