Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Manty

If Allis branded a chipper/shredder

Recommended Posts

Manty

Bought an old MacKissic chipper/shredder for $30 this fall that was in pretty tough shape but looked to have like-new knives and blades.  Since the engine looked to be shot, I planned on making a mount and running it with the tractor, but changed my mind when I got it tore apart.  Some panels were very rusted as it appeared the unit was left outside for decades...  I removed all the rusted pieces and welded new ones and put a predator engine on it - this way I could pull it into the woods and leave it there while I clean up brush.  Decided to paint it with some yellow paint I had around - looked better than the drab original green.  Used it this fall & it worked great!!

Chipper1.jpg

Chipper2.jpg

Chipper3.jpg

ChipperB4.jpg

  • Like 3

Share this post


Link to post
Share on other sites
Talntedmrgreen

Very cool!  I'd say you knocked this one out of the park.  That looks great.  I think you would find yourself tied up in conversation for the better part of a day if you had that setup at a show.

  • Like 2

Share this post


Link to post
Share on other sites
Snojetter

Looks terrific!

I ran an awful lot of brush and tops through one of these Mighty Macs when clearing our property for building.  It was slow going, but did a great job of reducing the piles to chips.  I ended up selling it after I started hauling brush piles out into the bog and letting it sink into the muck.  Much quicker process...but the chipper worked wonderfully!  I had thought about getting rid of the wheels and the flimsy frame and convert it to mount directly to my old Minnie-Mo RTU tractor and run it off the PTO.  That would have been an interesting project.

Share this post


Link to post
Share on other sites
macallis180

Well, Dave - I think you just upped the bar for some of the more talented guys on this website! (I'm not one of them).  That pairing looks fantastic.  Especially like the pinstriping on the chipper/shredder - just like the cowling on the tractor.

Share this post


Link to post
Share on other sites

  • Who's Online (See full list)

    • BLT
    • lt-scir
    • marksr
    • bowhunt4life
    • Al Truistic
    • Mach1martysr
    • mcd
    • bud119195
    • gwiseman
  • Today's Birthdays

    No users celebrating today
  • Recent Status Updates

    • Paul M.Murphy

      Paul M.Murphy

      Hello glad I got on this site. I hope to upload a couple of photos of my Simplicity Broadmoor 
      Model 707 Tractor. I have replaced all the belts on it and installed a new ignition switch.
      Have a mower deck which was in poor shape , repaced a couple of bushings and welded the
      deck where there was some holes. The tractor and mower deck came from a friend and the 
      mower deck metal was getting pretty thin. Some new metal was put in it and we also undercoated the underside of the deck. This was done by my friend Greg Toulman.
      I have not put the mower deck on the tractor yet, waiting for Greg to come home and give me a hand. Can you please tell me if there is a manual for the mower deck and where I could get one.
      I would also like to get some moon wheel discs as well.
      I will try and down load some photos of the tractor when my wife shows me how to. 
      I really love driving this tractor and also how well it is made compare today's tractors, especially the flexible rear end and the rollers.
      Tell the next time 
      Paul
       
      · 8 replies
    • jbrooks

      jbrooks  »  Talntedmrgreen

      Josh
       
      folowing  this from a link at the downloads.  I just rescued an AC 920 with the lambodini diesel. I can' t download  yet .  Where did you find the PDF copy you posted. . I would like to figure out how to adjust the injection pump. 
      I assume it's a bosche, correct
      · 0 replies
  • Adverts

×