Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Josiah deshong

620 fuel pump placement

Recommended Posts

Josiah deshong

I thought long and hard for a place to mount my fuel pump out of the way and so it looked like it wasn’t an after thought and this is what I came up with for my 620 allis. I took 16gauge steel and cut two ears and welded those ears to the back gas tank strap and then welded one stud on each ear to bolt the fuel pump to. By doing this I only had to run about 6 inches of wire to a new toggle switch  to turn it on and off. I’m still debating on the pumps placement for my 4040 because the hood doesn’t have the clearance like the allis in that area. Has anyone else found a good place for the fuel pump on the simplicity’s that’s out of the way and looks original any input would b appreciated

F28306E7-4E8C-4F35-9CD8-C3DB3F70C427.jpeg

C51B7C09-BDDA-41F0-8E45-6059B2D87587.jpeg

FD488154-5741-4321-BE0A-23A08DF0F23B.jpeg

Share this post


Link to post
Share on other sites
SimpleOrange

Wired my electric fuel pump to the power wire from ignition switch leading to the coil.

On your 4040 there's plenty of room inside the drive shaft tunnel for a fuel pump.

Share this post


Link to post
Share on other sites
720nut

Mine has a 90* plate that fits under front tank strap and is in front of the tank ,no clearance problems.

If I can find picture I'll post. Hope ya can see what I did here

DSCN1255.JPG

Edited by 720nut

Share this post


Link to post
Share on other sites
SimpleOrange
4 hours ago, 720nut said:

Mine has a 90* plate that fits under front tank strap and is in front of the tank ,no clearance problems.

If I can find picture I'll post. Hope ya can see what I did here

DSCN1255.JPG

Is that brown belt on the front PTO Kevlar the ones I'm using are green.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Who's Online (See full list)

    • simplewrench
    • Bear
    • Snojetter
  • Today's Birthdays

    No users celebrating today
  • Recent Status Updates

    • Paul M.Murphy

      Paul M.Murphy

      Hello glad I got on this site. I hope to upload a couple of photos of my Simplicity Broadmoor 
      Model 707 Tractor. I have replaced all the belts on it and installed a new ignition switch.
      Have a mower deck which was in poor shape , repaced a couple of bushings and welded the
      deck where there was some holes. The tractor and mower deck came from a friend and the 
      mower deck metal was getting pretty thin. Some new metal was put in it and we also undercoated the underside of the deck. This was done by my friend Greg Toulman.
      I have not put the mower deck on the tractor yet, waiting for Greg to come home and give me a hand. Can you please tell me if there is a manual for the mower deck and where I could get one.
      I would also like to get some moon wheel discs as well.
      I will try and down load some photos of the tractor when my wife shows me how to. 
      I really love driving this tractor and also how well it is made compare today's tractors, especially the flexible rear end and the rollers.
      Tell the next time 
      Paul
       
      · 8 replies
    • jbrooks

      jbrooks  »  Talntedmrgreen

      Josh
       
      folowing  this from a link at the downloads.  I just rescued an AC 920 with the lambodini diesel. I can' t download  yet .  Where did you find the PDF copy you posted. . I would like to figure out how to adjust the injection pump. 
      I assume it's a bosche, correct
      · 0 replies
  • Adverts

×