Jump to content

Unofficial Home of Old Simplicity & Allis-Chalmers Garden Tractors

Need to get back to projects


Chris727

Recommended Posts

What are some of your 2022

"need to get back to" projects? Please share here.

HB-112 needing vickers resealed and rear axle tube replaced as well as all new tires needed and mid-PTO repaired-installed.

 

IMG_0805.thumb.JPG.851573a64d4ff0fb2a6d5c9e079f5a6f.JPG

Agco 1918 needing cylinder head re-installed, fuel system cleaned and who knows what else.

1918_001.jpeg.96032a0d4b7ffc1bb41e50868890c2b7.jpeg

Rear axle tube seal is leaking terribly on the 75th. Its to a point that it may no longer be used. Need to remove the axle so I can replace the LH seal. 

IMG_3134.JPG.da2ab1aa1fc0c9ba1e0e5a8a9f3ba07d.JPG

Will probably kick this diesel on down the road if I can't get it running without much more tinkering. 

IMG_5589.thumb.jpg.348f1e91f963739eead31caddc2335a8.jpg

 

 

 

 

 

  • Like 4
Link to comment
Share on other sites

I am not one to make lists; they usually self-destruct anyway! 
I usually go out to the shop, look around, decide which project piques my interest that day.
Sometimes, a book in the LazyBoy wins out!

  • Like 3
  • Haha 2
Link to comment
Share on other sites

9020 starter issue, small leak on the Legacy maybe front seal, trying to decide if I'm actually going to do the diesel project or just shove it on down the road, right now getting tired of stepping over it and taking up space.

AS for Lazyboy spend to much time watching NHRA drag racing and Tractor pulling

Edited by 720nut
  • Like 2
Link to comment
Share on other sites

Finish the sprayer -build a boom w/3 spray tipsD643FA13-6D02-4299-BAAC-0FAC65FDAFDC.thumb.jpeg.3f2971f8fa2eea03a3518876bf4fa3a2.jpeg

Use the Easy Rake. Finished it but haven’t made a test run 0EEF9F38-B890-414E-A28F-AF78DD7D9F08.thumb.jpeg.801e6063517b5d82c9e7daa8a02bd498.jpeg

i think this may have been to look at rather than use. Wheels fastened w/lag screw/axles. Wheels lock as screw tightens..re-engineer maybe2B37A25C-906B-40C8-8BBB-0665E999362E.thumb.jpeg.15869fb1c89abd7a522e7a0ca49f5e00.jpeg

Finally start restoration on these 2 machinesC81823AA-77BB-4634-8BB6-5234A57F93FD.thumb.jpeg.60365106ca636c24d096a6538f7b5222.jpegD893CE4A-5B2E-4E77-BEBB-7E949F740CD3.thumb.jpeg.5a3a7e679e1255ccfb1a1b81797cc9df.jpeg

put my CH18 out of a CC back together. Been in pieces for 3 or 4 yrs.

Get a little use outta this bike I bought. Hip caused me to shelve it so far9268313F-53FB-4D1F-B52D-CAC673329BBD.thumb.jpeg.deb3ebd6e0a54628dc8a01d9709d30e0.jpeg

tear the weed cutter apart & rebuildA6BE330F-74E6-4FE2-995F-3CD12DBC798D.thumb.jpeg.49fbaf764a529ab541764593d9bb42fe.jpeg

Offer the Conquest for saleEB74F4E9-A6D8-4A37-B630-6DD18B71DAF8.thumb.jpeg.9ee7a9023b4282e0b9ee44e32c251b4c.jpeg

do more plowing9263074E-1164-4F36-B1D4-E6E37E6B3416.jpeg.33cc23e359f76cf8d6747f3860ab290b.jpeg

  • Like 4
Link to comment
Share on other sites

While I got most of the stuff on the 2021 list done this last year, plus a whole lot more, here are the 4 items from that list that still need done....

Quote

 

1 ) Replace the trailer brake controller on the F-250

2)  Build the electric winch setup to go into my 5x8 dump trailer

3) Build solar panel power station

4) swap heads on a head gasket blowing 27hp Kohler vertical command

 

This year for new ideas, just have 2 on my mind. Maybe...procuring a mini metal lathe and smaller bench top milling machine. 

  • Like 2
Link to comment
Share on other sites

On 1/2/2022 at 5:12 PM, SmilinSam said:

While I got most of the stuff on the 2021 list done this last year, plus a whole lot more, here are the 4 items from that list that still need done....

This year for new ideas, just have 2 on my mind. Maybe...procuring a mini metal lathe and smaller bench top milling machine. 

Sam , if I may say on the subject of a lathe and mill , look for a Bridgeport and at least a 10" lathe , I bought smaller still have them but found most of my projects required larger machines. 

If you look around the bigger machines can sometimes be bought cheaper than the smaller ones, guess maybe cause there a little harder to move , but you'll thank yourself in the end.

I need to teach myself again how to put comments with the photo's but that's another day.

My Bridgeport and Clausing 10in. lathe, second is my Millrite mill, nice little mill but I hardly use it anymore since I got the Bridgeport, third is a 18" Southbend lathe never got around to hooking it up yet 5hp 3 ph and was going to put that motor on my phaze convertor and 2 ph on lathe , but I'm no electriction may end up selling it and the Millrite

DSCN4337.JPG

DSCN4338.JPG

DSCN4339.JPG

  • Like 3
  • Thanks 1
Link to comment
Share on other sites

×
×
  • Create New...